Get 3 Free Quotes in Etobicoke
We'll match you with licensed contractors shortly.
Electricians in Etobicoke serve a wide range of housing stock — Mimico and Long Branch lakeshore bungalows built in the 1940s and 1950s with original 60-amp fuse panels that can no longer support modern loads, The Kingsway and Humber Valley mid-century detached homes requesting panel upgrades to 200 amps, and the newer townhouse and condo developments along The Queensway and in Islington that need EV charger circuits and Level 2 EVSE installation. In Rexdale and north Etobicoke (M9V, M9W), post-war semis and 1970s-era apartment buildings are common upgrade candidates. The Electrical Safety Authority requires an ESA permit for virtually all new or altered circuits in Ontario — including dedicated circuits for EV chargers, electric dryers, hot tubs, electric vehicle service equipment, and EV-ready rough-in conduit. A licensed electrical contractor (309A Master Electrician or C10-licensed contractor) must pull the permit; homeowners cannot pull ESA permits for work performed by a contractor. For older Etobicoke homes with aluminum branch circuit wiring from the 1960s–1970s, ask your electrician to assess the aluminum connections at devices and panels — improper termination of aluminum wiring is a known fire risk and should be addressed as part of any panel or circuit work. We will connect you with three licensed Etobicoke electricians.
Ready to get quotes for your Electrician in Etobicoke?
Free for homeowners · No obligation · Licensed Ontario tradesTell us your Etobicoke neighbourhood or FSA, the scope of work (panel upgrade, EV charger circuit, new outlets, rewiring, or other), your panel's current amperage if known, and your preferred timeline. Mention if your home has knob-and-tube or aluminum wiring so we can match you with electricians experienced with those systems.
Within 24 hours, three licensed Etobicoke electricians matched to your project type will contact you with itemized quotes covering labour, materials, permit fees, and any Toronto Hydro coordination required for service entrance work.
Confirm each electrician's Certificate of Qualification (309B for construction and maintenance, 309A for industrial) through the Skilled Trades Ontario registry. Verify the contractor firm's ESA C10 Electrical Contractor's licence. Ask for current WSIB clearance and proof of liability insurance.
Your electrician must pull the ESA permit before starting and is responsible for scheduling the ESA inspection on completion. For panel upgrades or service entrance work, confirm who coordinates the Toronto Hydro disconnect and reconnect — your electrician typically arranges this. Get permit responsibility, warranty on workmanship, and equipment specifications in writing.
Yes, for any new circuit, panel change, or alteration to existing wiring. The Electrical Safety Authority requires an ESA permit for dedicated circuits (EV chargers, dryers, hot tubs), panel upgrades, new outlets, and most rewiring work. Your licensed electrical contractor should pull the permit before starting; an ESA inspector will review the work and issue a certificate of completion. Skipping the permit voids homeowner's insurance coverage for electrical-origin fires and creates liability on property sale.
An Ontario licensed electrician must hold a 309B (Construction and Maintenance Electrician) Certificate of Qualification from the Ontario College of Trades for residential and commercial work. For industrial sites, a 309A certificate is required. The electrical contractor firm must hold a C10 Electrical Contractor's licence issued by the ESA. Verify both the individual's Certificate of Qualification and the contractor's C10 licence through the Skilled Trades Ontario registry before signing a contract. Also confirm current WSIB clearance and a minimum $2M commercial general liability insurance policy.
Most Etobicoke panel upgrades replace an original 60-amp or 100-amp fuse panel with a 200-amp breaker panel to support modern loads including EV chargers, electric ranges, and air conditioning. The work involves disconnecting hydro at the meter (coordinated with Toronto Hydro), replacing the panel and service entrance conductors, installing a new meter base if required, and reconnecting all branch circuits. Toronto Hydro must reconnect the service after the ESA inspection — plan for a service interruption of half a day to a full day. In older Etobicoke homes with knob-and-tube or aluminum wiring, your electrician should assess whether circuits need remediation as part of the upgrade scope.
Yes. A Level 2 EV charger (240V, 32–50A) requires a dedicated circuit from your electrical panel, an ESA permit, and installation by a licensed electrical contractor. For Etobicoke homes with 60-amp or 100-amp panels, a panel upgrade is typically required before a Level 2 circuit can be added — confirm panel capacity with your electrician during the quote. Toronto Hydro offers an EV Time-of-Use rate that can reduce charging costs; ask your electrician to confirm the circuit is metered correctly if you want to access that rate. The Canada Greener Homes Loan covers EV-ready rough-in conduit as an eligible measure.
ESA permits are required for new or altered circuits in Ontario; your licensed electrical contractor must apply for and close the permit before energizing new work
Some electrical scopes — service entrance work, major panel replacements, or work tied to additions — may also require a City of Toronto building permit; confirm with your contractor
Ontario electricians must hold a 309A (Industrial Electrician) or 309B (Construction and Maintenance Electrician) Certificate of Qualification; verify credentials before hiring